EPA Subpart RRR compliance for Aluminum Recyclers

Where does dust and fume extraction help with compliance

What is Subpart RRR?

Subpart RRR (40 CFR Part 63, Subpart RRR) is the US EPA's National Emission Standards for Hazardous Air Pollutants (NESHAP) for secondary aluminum production. It limits particulate matter (PM), hydrogen chloride (HCl), hydrogen fluoride (HF), dioxins and furans (D/F), and total hydrocarbons (THC) from scrap processing, melting, fluxing, and dross operations at aluminum recycling plants.

The emission limits get most of the attention, but many compliance problems start upstream of the stack. A furnace meets its limits only if the fume is captured at the hood, carried through the duct, and treated in a collector sized for the plant's current scrap mix. That makes dust and fume extraction the part of the system that often decides whether a plant passes its next performance test.

This guide covers who the rule applies to, where compliance pressure is building for recyclers, and what a well-designed extraction system needs to deliver.

Who does Subpart RRR apply to?

Subpart RRR applies to any facility that uses clean charge, aluminum scrap, or dross as a raw material and performs at least one of these processes: scrap shredding; scrap drying, de-lacquering, or decoating; thermal chip drying; furnace operations such as melting, holding, sweating, refining, fluxing, or alloying; dross recovery; inline fluxing; or dross cooling (40 CFR 63.1503).

What a plant must do depends on its hazardous air pollutant (HAP) status:

  • Major sources must meet the full set of limits for PM, HCl, HF, D/F, and THC across shredders, dryers and kilns, furnaces, dross equipment, and secondary aluminum process units (SAPUs).
  • Area sources are subject only to the D/F requirements, and only for specific units, including SAPUs with Group 1 furnaces that process anything other than clean charge.

The foundry and die caster exemption

Aluminum foundries, die casters, and extruders are not treated as secondary aluminum production facilities if they melt only clean charge, customer returns, or internal scrap, and do not operate sweat furnaces, thermal chip dryers, or scrap dryers, delacquering kilns, or decoating kilns.

That exemption is lost in two common ways. The first is buying contaminated scrap from outside the company: internal scrap qualifies regardless of contamination, but only while it stays within the control of the company that produced it. The second is installing one of the listed thermal units. One narrow carve-out applies: an area-source foundry covered only because it runs a thermal chip dryer does not bring its furnaces under the rule, as long as those furnaces melt only clean charge, internal scrap, or customer returns.

Group 1 vs. Group 2 furnaces

A furnace's group decides whether it carries emission limits, and two things determine the group: what goes into the furnace and how it is fluxed.

Furnace typeWhat it meltsFluxingWhat applies
Group 1Aluminum with paint, lubricants, coatings 
or other foreign material, or clean charge
Any, for contaminated charge; 
reactive fluxing, for clean charge
Emission limits for PM, HCl, 
HF and D/F (major sources); 
D/F (area sources, when processing other than clean charge)
Group 2Clean charge onlyNone, or only nonreactive, non-HAP agents

Operating requirements, no numerical emission limits


Two details move furnaces between groups. First, reactive fluxing means any flux other than cover flux that produces a HAP emission. Chlorine degassing or demagging therefore turns a clean-charge furnace into a Group 1 furnace, while argon and nitrogen are not reactive.

Second, the definition of clean charge covers more than ingot and sow. It includes scrap dried at 650F (343C) or higher, scrap delacquered or decoated at 900F (482C) or higher, and runaround scrap free of paint or coatings. Anodized aluminum with dyes or sealants containing organic compounds is not clean charge (40 CFR 63.1503). The performance of a decoating kiln directly affects how much contamination reaches the furnaces downstream.

Five places Subpart RRR compliance needs to be reviewed

Most established recyclers already operate permitted, tested systems. The risk is not routine operations, it's change. These five points are where a dust and fume collection system that passed last time can fall behind.

  1. New capacity brings new obligations

    A new SAPU is any combination of Group 1 furnaces and in-line fluxers constructed or reconstructed after February 11, 1999 (40 CFR 63.1503). New furnaces need initial performance testing, and their emissions must fit within the SAPU calculation. Capture and control equipment is usually specified well before the furnace starts up, so emission control belongs in the project from the first design review.

  2. Dirtier scrap changes the load on the collector

    Recyclers are taking in more post-consumer scrap, including used beverage cans and coated automotive material. More paint, lacquer, and oil means more organics to destroy and more chlorine-driven chemistry in the furnace. That raises the acid gas and D/F load on a baghouse originally sized for cleaner feed.

  3. Capture efficiency is a compliance requirement

    Subpart RRR ties capture and collection to the ACGIH Industrial Ventilation guidelines. Since the 2015 amendments, performance tests also require temporary hooding that meets those guidelines, or a petition filed 180 days before the test if hooding is impractical. Fume that escapes at charging doors, sidewells, or skimming is never measured at the stack, but it is a test-day and inspection risk.

  4. There is no startup and shutdown exemption

    The 2015 final rule removed the separate startup, shutdown, and malfunction provisions. Emission limits now apply during startup and shutdown, with their own compliance demonstration requirements, and the SSM plan requirement is gone. The extraction and control system has to be running and stable before the furnace is.

  5. Operating headroom is production headroom

    Operating limits are set during the performance test and then monitored continuously. Typical parameters include lime injection rate, baghouse inlet temperature, reactive flux injection rate, and bag leak detection alarms. A collector running at the edge of its capacity effectively caps how much flux a plant can use and how much metal it can push through.

Matching each affected source to its extraction and control approach

Each Subpart RRR affected source has its own pollutant profile, so each needs its own capture point and control approach. This table summarizes common practice; the right design for a given plant depends on its permit, its scrap mix, and its existing equipment.

Affected sourceMain pollutantsTypical extraction and control approach
Scrap shredderPMHooded capture at feed and discharge points, ducted to a baghouse; 
cyclone pre-separation for coarse material
Thermal chip dryerTHC, D/FAfterburner to destroy organics, followed by particulate control
Scrap dryer / delacquering / decoating kilnTHC, D/F, HCl, PMAfterburner, then a lime-injected baghouse
Sweat furnaceD/FAfterburner, with capture verified against ACGIH design or 
an alternative airflow test
Group 1 furnace (SAPU)PM, HCl, HF, D/FClose-capture hooding at charging, fluxing, skimming and tapping; 
lime-injected baghouse, with activated carbon where D/F control requires it
In-line fluxerHCl, PMEnclosure exhaust to a lime-injected baghouse, often shared with the furnace system
Dross cooling and handlingPMEnclosed cooling and transfer points ducted to a baghouse

For reference, the Group 1 furnace limits at major sources include 0.4 lb PM per ton of feed (0.80 lb/ton for a melting/holding furnace processing only clean charge), 0.40 lb HCl per ton or 10% of uncontrolled HCl with an add-on control device, 0.40 lb HF per ton for an uncontrolled furnace, and 2.1 x 10-4 grains D/F TEQ per ton of feed (40 CFR 63.1505). Always confirm current values in the eCFR and your permit.

What good dust and fume collection looks like

A Subpart RRR extraction system works as one chain: capture, transport, treatment, and monitoring. A weak link anywhere shows up as a failed test, a parameter excursion, or fugitive emissions in the melt shop.

Capture at the source

Hoods should be designed to ACGIH guidelines for each emission point: charging doors, sidewells, fluxing ports, skimming, and tapping. Cross-drafts from open doors and traffic aisles, door-open cycles, and the plume rise from hot metal all affect capture velocity. Airflow should be verified after any changes to the furnace, the building, or the duct system.

Transport without dropout or ignition risk

Duct velocities need to keep particulate moving without excessive wear or pressure loss. Aluminum fines are combustible, so ductwork and collectors handling them should follow the applicable NFPA combustible dust standards, with attention to spark control, isolation, and explosion protection.

Treatment sized for today's scrap and tomorrow's

A lime-injected baghouse is the workhorse for Group 1 furnaces and in-line fluxers. Lime (calcium oxide or another alkaline reagent) is added continuously upstream of the fabric filter, where it neutralizes HCl and HF while the filter captures particulate (40 CFR 63.1503). Activated carbon can be added where D/F control requires it. The collector, sorbent feed, and inlet cooling should be sized for peak acid gas loads from the dirtiest scrap the plant expects to buy, not the average of last year's feed.

Monitoring that holds up on audit

Bag leak detection, differential pressure, sorbent feed rate, and inlet temperature are the parameters inspectors look at first. They should be recorded reliably, alarmed sensibly, and maintained in line with the plant's operation, maintenance, and monitoring plan.

How Nederman MikroPul supports recyclers

Nederman MikroPul designs fabric filtration and dry sorbent injection systems for secondary aluminum. These include flat-bag baghouses and additive dosing for HCl, HF, and SOx, for scrap processing, delacquering, melting, fluxing, dross handling, and pouring. Nederman MikroPul's capture and ventilation expertise covers the hoods and ductwork that feed those collectors, and its aftermarket service supports filter media, inspections, and performance before scheduled tests.

Frequently Asked Questions

Usually not. Foundries, die casters and extruders are exempt if they melt only clean charge, customer returns or internal scrap and do not run sweat furnaces, thermal chip dryers, or scrap dryers or decoating kilns. Buying contaminated outside scrap or adding one of those thermal units can bring a facility under the rule.

A Group 2 furnace melts only clean charge and uses no reactive flux. A Group 1 furnace melts contaminated aluminum, or melts clean charge with reactive flux such as chlorine. Group 1 furnaces carry emission limits; Group 2 furnaces are subject to operating requirements instead.

The rule regulates particulate matter (as a surrogate for metal HAPs), hydrogen chloride, hydrogen fluoride, dioxins and furans, and total hydrocarbons. Which limits apply depends on the emission unit and on whether the plant is a major or an area source of hazardous air pollutants.

Yes. EPA's 2015 amendments removed the separate startup and shutdown provisions, so emission limits apply during those periods, with specific compliance demonstration requirements. The SSM plan requirement was also removed. Extraction and control equipment must be running and stable before furnace operations begin.

Fluxing and contaminated scrap produce acid gases (HCl and HF) along with fine particulate. Injecting lime upstream of a baghouse neutralizes the acid gases, and the fabric filter captures the reacted sorbent and the particulate together. Activated carbon can be added for dioxin and furan control.

The most recent substantive amendments came from EPA's 2015 residual risk and technology review, which added HF limits, revised testing requirements and removed the SSM exemption. Regulations can change, so check the current eCFR text and your state permit before making compliance decisions.

Request a Subpart RRR extraction system audit

Planning an expansion, changing your scrap mix or preparing for your next performance test? A Nederman MikroPul engineer can review your extraction and control system against the demands Subpart RRR places on it: 

  • Capture airflow at each hood compared with ACGIH design guidance
  • Collector condition, air-to-cloth ratio and sizing against current and planned scrap
  • Sorbent dosing capacity and inlet temperature control
  • Monitoring readiness, including bag leak detection and parameter recording
  • Combustible dust protection on ductwork and collectors

This article is general information, not legal advice. A system audit is an engineering review; your permit, your state agency and your environmental counsel determine compliance status.